DSpace logo

Por favor, use este identificador para citar o enlazar este ítem: http://repositorio.utmachala.edu.ec/handle/48000/11062
Registro completo de metadatos
Campo DC Valor Lengua/Idioma
dc.contributor.authorCruz Sanchez, Daniel Patricio-
dc.date.accessioned2017-09-07T17:56:33Z-
dc.date.available2017-09-07T17:56:33Z-
dc.date.issued2017-08-25-
dc.identifier.citationCruz Sanchez, D.P. (2017) Simulación de una red de distribución de agua potable para edificaciones mediante la aplicación del software epanet (examen complexivo). UTMACH, Unidad Académica de Ingeniería Civil, Machala, Ecuador. 26 p.es_ES
dc.identifier.otherTUAIC_2017_IC_CD0017-
dc.identifier.urihttp://repositorio.utmachala.edu.ec/handle/48000/11062-
dc.descriptionThis report had as its main objective to simulate a network of drinking water for buildings using the EPANET software since thanks to technological progress, these new programs have been implemented to check the behavior of the network, the method that I use was that of simultaneity factor since this project was based on all kinds of building the standard drainage system Ecuatoriana (NHE) was used and took the parameters necessary to implement the system chosen for the property was an indirect system, and so were estimates on the size of the tanker and subsequent to that elevated tank pumping system necessary for the supply of water in the building, following proper procedure was designed and calculation network of internal distribution of water, thus obtaining the corresponding pressures in each one of the knots and subsequent to that is designed the same network in EPANET software found the behavior of the network, but for that they had to modify some parameters like inbound flows each equipment since the program does not take into account simultaneity factor and the results of that analysis was that he was obtained negative pressures completely away from which they obtained in the worksheet and Therefore the longitudinal profiles of each plant left below the reference level.es_ES
dc.description.abstractEl presente informe tuvo por objetivo principal simular una red de agua potable para edificaciones utilizando el software EPANET ya que gracias al avance tecnológico se han implementado estos nuevos programas para comprobar el comportamiento de la red, el método que se empleo fue el del factor de simultaneidad debido a que este proyecto se basó en todo tipo de edificación, se empleó la Norma Hidrosanitaria Ecuatoriana (NHE) y se tomaron los parámetros necesarios a implementar ya que el sistema escogido para el inmueble fue un sistema indirecto, y así se realizaron los cálculos del dimensionamiento de la cisterna y tanque elevado posterior a eso el sistema de bombeo necesario para el abastecimiento de agua en el inmueble, siguiendo el procedimiento adecuado se diseñó y calculo la red de distribución interna de agua potable obteniendo así las presiones correspondientes en cada uno de sus nudos y posterior a eso se diseñó la misma red en el software EPANET y se comprobó el comportamiento de la red, pero para eso se tuvo que modificar algunos parámetros como los caudales entrantes cada uno de los aparatos debido a que el programa no toma en cuenta el factor de simultaneidad y los resultados de dicho análisis fue que se obtuvo presiones negativas totalmente alejadas de las que obtuvo en la hoja de cálculo y por lo tanto los perfiles longitudinales de cada planta salieron debajo del nivel de referencia.es_ES
dc.format.extent26 p.es_ES
dc.language.isoeses_ES
dc.publisherMachalaes_ES
dc.rightsopenAccesses_ES
dc.rights.urihttp://creativecommons.org/licenses/by-nc-sa/3.0/ec/es_ES
dc.subjectDISTRIBUCIÓN, FACTOR DE SIMULTANEIDADes_ES
dc.subjectCAUDAL, EPANET, RED DE AGUA POTABLEes_ES
dc.titleSimulación de una red de distribución de agua potable para edificaciones mediante la aplicación del software epanetes_ES
dc.typeExamen Complexivoes_ES
dc.emailDpcruz_est@utmachala.edu.eces_ES
dc.cedula0706469160es_ES
dc.utmachtitulacion.titulacionExamen complexivoes_ES
dc.utmacharea.areaconocimientoIngeniería, Industria y Construcciónes_ES
Aparece en las colecciones: Examen Complexivo Ingeniería Civil

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
TUAIC_2017_IC_CD0017.pdf1,45 MBAdobe PDFVisualizar/Abrir


Este ítem está sujeto a una licencia Creative Commons Licencia Creative Commons Creative Commons